精品欧美乱码久久久久久,麻豆黄色录像带,成人国产精品黄色,123区日本人日逼

銷售咨詢熱線
15953126901
15153196527
行業動態 dongnews
企業案例 case

聯系我們

  • 聯系人:濟南燕翔鐵藝制品有限公司
  • 手機:15953126901
  • 電話:15153196527
  • 郵箱:785385551@qq.com
  • 地址:濟南市天橋區歷山北路黃臺不銹鋼市場3區317
當前位置: 首頁 > 新聞資訊>行業動態

鐵藝護欄的安裝流程介紹

來源:http://eastagcn.com.cn 日期:2024-07-08 發布人: 瀏覽次數:1

其實說道鐵藝護欄,我想大家應該沒有誰會陌生,畢竟它現在已廣泛應用在很多地方,我們到處可見,比如:幼兒園鐵藝護欄、學校、辦公區、工廠等等。但對于它的施工,應該沒有幾個非業內人士知道的,這里誠信不銹鋼鐵藝客服部人員給大家講述一些鐵藝護欄施工的基本流程。

Actually, when it comes to wrought iron guardrails, I think no one is unfamiliar with them. After all, they are widely used in many places and can be seen everywhere, such as kindergarten wrought iron guardrails, schools, office areas, factories, and so on. But for its construction, few non industry insiders should know about it. Here, the customer service department of Chengxin Stainless Steel and Iron Art will explain some basic processes for the construction of iron guardrail.

一、工程流程:

1、 Engineering process:

1、安裝預埋件

1. Install embedded parts

2、放線

2. Line up

3、安裝立柱

3. Install the pillar

4、扶手與立柱連接

4. Connection between armrest and pillar

5、打磨拋光

5. Polish and polish

二、安裝預埋件(后加埋件)

2、 Install embedded parts (add embedded parts later)

鐵藝護欄預埋件的安裝只能采用后加埋件做法,其做法是采用膨脹螺栓與鋼板來制作后置連接件,先在土建基層上放線,確定立柱固定點的位置,然后在地面上用沖擊鉆鉆孔,再安裝膨脹螺栓,螺栓保持足夠的長度,在螺栓定位以后,將螺栓擰緊同時將螺母與螺桿間焊死,防止螺母與鋼板松動。扶手與墻體面的連接也同樣采取上述方法。

The installation of embedded parts for wrought iron guardrails can only be done using the method of adding embedded parts after installation. The method is to use expansion bolts and steel plates to make rear connectors. First, lay out the line on the civil foundation to determine the position of the column fixing point. Then, drill holes on the ground with an impact drill and install expansion bolts. The bolts should be kept of sufficient length. After the bolts are positioned, tighten them and weld the nuts and screws together to prevent loosening of the nuts and steel plates. The connection between the armrest and the wall surface also adopts the above method.

三、放線

3、 Line up

由于上述后加埋件施工,有可能產生誤差,因此,在立柱安裝之前,應重新放線,以確定埋板位置與焊接立桿的準確性,如有偏差,及時修正。應保證鐵藝立柱全部座落在鋼板上,并且四周能夠焊接。

Due to the possibility of errors in the construction of the embedded parts mentioned above, it is necessary to re lay the line before installing the column to determine the accuracy of the buried plate position and the welded column. If there is any deviation, it should be corrected in a timely manner. It should be ensured that all iron columns are seated on steel plates and can be welded around them.

20201126055137960.jpg

四、安裝立柱

4、 Install the pillar

焊接立柱時,需雙人配合,一個扶住鋼管使其保持垂直,在焊接時不能晃動,另一人施焊,要四周施焊,并應符合焊接規范。

When welding the column, two people need to cooperate. One person should hold the steel pipe to keep it vertical and not shake during welding, while the other person should weld around it and comply with the welding specifications.

五、扶手與立柱連接

5、 Connection between armrest and pillar

立柱在安裝前,通過拉長線放線,根據場地的傾斜角度及所用扶手的圓度,在其上端加工出凹槽。然后把扶手直接放入立柱凹槽中,從一端向另一端順次點焊安裝,相鄰扶手安裝對接準確,接縫嚴密。相鄰鋼管對接好后,將接縫用鐵藝焊條進行焊接。誠信不銹鋼鐵藝客服部提醒:焊接前,必須將沿焊縫每邊30~50mm范圍內的油污、毛刺、銹斑等清除干凈。

Before installing the column, a groove is machined at its upper end based on the inclination angle of the site and the roundness of the handrail used by stretching the line. Then place the handrail directly into the groove of the column, and install it by spot welding from one end to the other in sequence. The adjacent handrails should be installed accurately and the joints should be tight. After connecting adjacent steel pipes, weld the joints with iron welding rods. The customer service department of Chengxin Stainless Steel Iron Art reminds that before welding, the oil stains, burrs, rust spots, etc. within a range of 30-50mm along each side of the weld must be removed completely.

六、打磨拋光

6、 Polish and polish

全部焊接好后,用手提砂輪機將焊縫打平砂光,直到不顯焊縫。拋光時采用絨布砂輪或毛氈進行拋光,重慶不銹鋼欄桿施工人員提醒,同時采用相應的拋光膏,直到與相鄰的母材基本一致,不顯焊縫為止。

After all welding is completed, use a handheld grinder to level and sand the weld seam until it is no longer visible. When polishing, use a velvet grinding wheel or felt for polishing. Chongqing stainless steel railing construction personnel remind and use the corresponding polishing paste until it is basically consistent with the adjacent base material and there is no visible weld seam.

亚洲三级无码人妻AV| 婷婷五月天网址导航| 欧美午夜一道本一二区| 亚洲欧美国产中文另类精品| 日本少妇 内射| 久久久狠狠色精品| 午夜福利小视频在线观看视频| 一区二区精品精| 网红毛片免费看| 亚洲精品成人黄色片| porn 一区二区| 中文字幕在线不卡精品| 91熟女偷情视频| 日韩激情精品| 热久伊人干干| 亚洲Vs久久久| 两性生活视频日韩| 大香蕉国产经典在线| 午夜精品精品| AV中国一区二区| 亚洲综合激情自拍| 大鸡巴操逼免费剧情一级片| 人人操人人弗| 国产婷婷亚洲| 五月好色婷婷| 久婷婷另类一区| 国产粉嫩馒头无套在线观看| 天天做天天干天天舔| 白虎操逼一区二区| 巨吊一区二区三区| 熟妇人妻一二三区免费| 欧美老婷婷在线一区| 欧美特级一区二区黄片| 爽天天天天天天天日| 欧洲乱码在线观看一区二区| 欧美人妻人人| 日本美女翘屁股操b| 国产性感黄| 非洲在线一区二区| 黄片香蕉社区| 好吊妮手机视频播放|